|
A
Available in heights of 6″, 12″,
24″, 30″ 36″, 42″, 48″, 54″, 60″, 66″, 72″, 78″, 84″, 90″, 96″, 108″ & 120″
High. One-Piece trim (Two-Piece if 108″ & 120″) snaps onto first & last
Uprite or Extension Uprite. Can be used on both sides of Extension Uprites
where Extension Backs are not used.
Top rail is designed to hold back panels in place
from the top of the shelving unit.
All Island and Wall Sections
require at least one Top, Center, & Bottom Rail. 78”H – 120”H require one
Splicer Rail. 96”, 108”, 120”H require two Center Rails.
Electrical knockouts included on all Rails. 2’ & 30” sections use (2) Top
Rails to make a Splicer Rail.
E
Designed to hold the back boards in place and from
imploding inwards for Lozier Shelving
All Island and Wall Sections
require at least one Top, Center, & Bottom Rail. 78”H – 120”H require one
Splicer Rail. 96”, 108”, 120”H require two Center Rails.
Electrical knockouts included on all Rails. 2’ & 30” sections use (2) Top
Rails to make a Splicer Rail.
G
Designed to hold back boards in place for Lozier
Shelving Units.
All Island and Wall Sections
require at least one Top, Center, & Bottom Rail. 78”H – 120”H require one
Splicer Rail. 96”, 108”, 120”H require two Center Rails.
Electrical knockouts included on all Rails. 2’ & 30” sections use (2) Top
Rails to make a Splicer Rail.
I
Spring Locking Base Bracket.
Available in 13″, 16″, 19″,22″, 25″, 28″ & 31″Depths. Base height: “06″ or
“LB” Low Base. 2″ conduit hole for greater electrical access. Included
Leveling Legs for uneven flooring. Install straight in using integral
spring latch
K
Available in 24″, 30″, 36″ or 48″
Widths. Base height: “06″ or “LB” Low Base. Snaps in place.
Fits flush with floor regardless of leveling adjustments. 36″ & 48″W
Fronts have an electrical knockout.
Extension uprights designed to
extend the height of an existing Gondola or Wall section of Lozier Wall
Shelving.
|
B
Available in heights of 36″, 42″, 48″, 54″, 60″, 66″, 72″,
78″, 84″, 90″, 96″, 108″ & 120″ High. Use for Wall & Island Sections.
Steel Welded construction. 3/16″ thick face channel. 1″ slotted on center
for maximum flexibility. Includes side flanges to retain back material.
Includes leveling leg for uneven floors. Includes top caps on Uprites 36″
– 66″ High
Lozier backs and extension backs available in a
Pegboard, Hardboard, Slotwall, and Wire Grid for all Lozier Shelving Units.
F
Used to hold and align back boards on 78" and higher
Lozier Shelving Units and when adding Extension Uprights to existng shelving.
All Island and Wall Sections
require at least one Top, Center, & Bottom Rail. 78”H – 120”H require one
Splicer Rail. 96”, 108”, 120”H require two Center Rails.
Electrical knockouts included on all Rails. 2’ & 30” sections use (2) Top
Rails to make a Splicer Rail.
H
Available in 13″, 16″, 19″, 22″,
25″, 28″ or 31″ Depths. Base Height: “06″ or “LB” Low Base. Attaches to
the first & last Base Bracket
J
Available in 13″, 16″,
19″,22″, 25″, 28″ & 31″Depths and in 24″, 30″, 36″ or 48″ Widths
Anchor Plates used when Shelving
Unit exceeds height to depth ratio limits. Required for Shelving over 5’H
in certain seismic zones. Secures Leveling Leg to floor using anchor bolts
(not included). Multi-Purpose Anchor for end of run, Wall End
Display or limited access applications.
The solution for maintaining separation of
school, office and art supplies. Dividers are 3 3/4" wide x 7 3/4" high x 6 3/4"
deep. The dividers clip into front shelf perforations. Minimum product width is
6". End dividers are sold separately and in pairs. |
